AODD Energy Assessment: Measure Air Cost per Cubic Metre of Liquid

Executive summary

AODD能源比較應該回答一個過程問題:在定義的條件下,需要多少公用事業投入才能輸出商定的液體量? 僅僅比較最大額定流量或壓縮機排出壓力並不能回答這個問題。

隔膜泵空氣消耗計算應從測量的公用事業輸入和有用液體輸出開始。 在決定如何降低隔膜泵空氣消耗之前,應建立一個可重複的基線。

This paper provides a plant-level screening method using measured air volume, measured liquid output and an explicitly stated air-cost basis. It is not a certified performance test or a claim about a particular pump model. Its worked example uses assumed numbers solely to demonstrate the calculation.

1. Define the comparison boundary

對於僅僅是泵的比較,測量泵的供氣量和通過泵的出口系統輸送的液體量。 如果問題涉及到生產線,則應在清楚描述的線路邊界內包括相關的分支泄漏、閒置消耗量和操作順序。

Keep the boundaries consistent between the baseline and proposed arrangement. It is misleading to charge all compressor-room losses to one option but compare it with only the drive input of another. It is equally misleading to attribute every reduction in air demand to an immediate reduction in compressor electricity.

空氣分配設計會影響耗氣量。 Wilden 描述了在泵行程結束時減少不必要的進氣量是 Pro-Flo SHIFT 操作理念的一部分。 將設計要求視爲測試配置的理由,而不是可轉讓的節省保證。 [R6]

2. Record a comparable operating condition

Identify the pump configuration, diaphragm and check-valve arrangement. Record fluid temperature, density and viscosity where available; inlet conditions; discharge pressure; and the normal operating sequence. The same nominal pump size can operate at different effective duties after a hose, valve or filter is changed.

Use an air meter suitable for the expected range and pulsating service, and document the installation requirements. State the reference pressure and temperature used for normalized air volume. Do not mix actual compressed volume, standard cubic feet and normal cubic metres without a documented conversion basis.

Measure liquid volume independently where possible, using an appropriate flow instrument or a calibrated collection method. Where mass is used, convert it using density at the relevant condition. A counter multiplied by a catalogue displacement can be a diagnostic estimate, but it should not silently replace measured delivery in a savings claim.

3. Diaphragm pump air consumption calculation

For a matched test interval:

Specific air consumption = normalized air volume / delivered liquid volume.

Express the result as Nm³ of air per m³ of liquid only when the chosen normal reference conditions are declared. A lower value means less measured air was used for the same delivered liquid quantity within that test boundary. It does not, by itself, describe product quality, transfer time or equipment life.

For an annual screening estimate:

年度空氣成本=年液體量×比空氣消耗量×分配空氣成本。

The allocated air cost should be supplied by the plant's utility team. It may include more than electrical energy. Label the basis so that different departments do not compare incompatible figures.

4. Worked example – assumed values, not field results

Suppose two acceptable operating arrangements each deliver 5 m³ of the same liquid at the required duty. The baseline consumes 150 Nm³ of air; the alternative consumes 120 Nm³. Assume annual liquid delivery of 6,000 m³ and an allocated air cost of USD 0.025 per Nm³.

The assumed difference is 36,000 Nm³ of air and USD 900 per year on the selected allocation basis. Specific air consumption falls by 20%. These results follow from the assumptions; they are not a WILLEE test, a manufacturer guarantee or a forecast for an unidentified installation.

If the installed incremental cost were USD 3,000, a simple utility-only payback would be approximately 3.3 years. That excludes maintenance differences, installation disruption, financing and the time value of money. A purchasing decision should identify those omissions rather than hiding them inside an apparently precise return figure.

5. Separate air savings from electricity savings

The compressor's control strategy matters. Reduced pump demand may reduce loaded operating time, avoid starting another compressor or simply increase unloaded running. The electrical response can differ in each case. Ask the utility team to estimate marginal electricity savings from the measured change in demand, preferably with compressor power records.

Graco 的 QUANTM 信息描述了電動驅動和節能潛力,但現場計算仍然需要匹配的流體負荷和測量或合理的電氣輸入。 正確的問題不是手冊中的百分比是否令人印象深刻,而是擬議的泵是否以更低的整個系統成本產生所需的輸出。 [R1]

6. Test the result before approving it

Repeat runs after steady operation is established, and include representative start, stop and emptying behavior if it matters to the production cycle. Keep raw measurements, instrument identification and the conditions for each run. A single favorable reading can conceal a change in source level or fluid temperature.

The comparison should report throughput and transfer time alongside utility intensity. Reducing pump speed may reduce instantaneous air use while extending the shift or missing the production target. Check that every candidate meets the same acceptance conditions.

For a first uncertainty check, compare the size of the claimed improvement with meter accuracy and run-to-run variation. Do not report decimal-level savings when the input readings or air-cost allocation are only approximate. State whether the economic result is a screening estimate or a measured operating comparison.

7. Practical decision record

Document the original problem, tested configurations, measurement boundary, accepted process duty and financial assumptions on one record. Retain photographs of the installed air connection and liquid pipework; these make later comparisons reproducible. Wilden's installation guidance emphasizes avoiding unnecessary piping restrictions, which can otherwise confound a pump comparison. [R7]

WILLEE can help structure an enquiry using the pump code, flow requirement, discharge condition and available utility measurements. A credible energy proposal begins with a reproducible duty, not an unsupported promise of a fixed percentage reduction.

討論一個AODD能源評論